USES:
TimberWash removes
dirt, grime, mildew stains, previous coatings (not paint) and
weathered graying from horizontal and vertical wood surfaces.
TimberWash is recommended for surface preparation prior to application
or reapplication of clear finishes and stains. For best results
use Saver Systems water repellent wood finishes. Note:
TimberWash will darken redwood. Use TimberBrite TM
wood brightener to clean and brighten redwood or as a neutralizer
to further brighten other wood species that have been cleaned
with TimberWash.
|
BENEFITS:
* Restores the natural
beauty of wood.
* Contains no acid or chlorine bleach.
* Safe for plants and animals.
* Biodegradable
|
DIRECTIONS
FOR USE:
Use 6 ounces (3/4
cup) of TimberWash powdered concentrate with each gallon of water. |
STEP 1 * MIX: Mix with water and stir thoroughly
until powder is mostly dissolved. Powder dissolves faster in
warm water. Solution should be used within six hours of mixing. |
STEP 2 * APPLY: Horizontal
Surfaces - Dampen
surface with water before application. Apply TimberWash solution
with sprayer, brush, or mop, working on small areas, (20-30 sq.
ft.) at a time. Vertical Surfaces - Dampen surface
with water before application. Apply with a sprayer working on
small areas at a time. Begin at the bottom and work to the top. |
STEP 3 * BRUSH: Horizontal
Surfaces - Let
solution stand approximately 5-10 minutes, keeping area wet with
additional TimberWash solution. Thoroughly scrub with a stiff,
short bristle broom or brush. Vertical Surfaces
- Let solution stand approximately 5-10 minutes, keeping surfaces
wet with additional solution. Thoroughly scrub with a stiff,
short bristle broom or brush working from bottom to top. TimberWash
will open wood pores and some raising of wood fibers may occur. |
STEP 4 * RINSE: Rinse thoroughly with water from
hose or pressure washer (minimum 1500 p.s.i.), using lowest pressure
that cleans without damaging the wood. Repeat steps 2-4 on next
small area. Rinse cleaned area of vertical surfaces to avoid
streaking as work progresses. Allow wood surfaces to thoroughly
dry before applying Saver Systems water repellent wood finishes.
Heavily weathered or soiled surfaces may require a second application.
Coverage: One gallon of TimberWash cleans and restores
100-200 square ft. depending on wood porosity.
|
HEALTH
AND SAFETY:
Avoid contact with
eyes and prolonged skin contact. Harmful if swallowed. Solution
will not harm grass or most plants. Rinse grass and plants
thoroughly with water after exposure. For more information,
consult the Material Safety Data Sheet.
Caution: Accumulation of product on ladders, scaffolding,
decks, etc. may result in a slippery surface.
|
LIMITED
WARRANTY:
Saver Systems warrants
this product to be free from defects. Saver Systems' liability
shall be limited in all events to supplying enough product to
re-treat the specific areas to which defective product has been
applied. Saver Systems shall not have any other liability including
direct, incidental, or consequential damages.
|
AVAILABILITY
AND COST:
TimberWash is available
from distributors and dealers throughout North America. Specific
job costs may be obtained from any Saver Systems distributor or
dealer.
|
PACKAGING:
TimberWash is available
in 2.25 lb. and 10 lb. recyclable plastic containers. The 2.25
lb. container of concentrate will make 5 Gallonss of TimberWash
cleaner; the 10 lb. container will yield 25 Gallonss.
|
TRANSPORT
& STORAGE:
TimberWash is not
considered hazardous under Department of Transportation regulations.
Do not stack pallets. Store in cool dry area.
|
Top of page! |